Truck Explorer PRO v3.0 (original)

Description

Full description:

1. License MB MEMO
A program module for Read & Write FLASH & EEPROMs of engine control module PLD/MR based on microprocessor C167 without internal flash. This function allows making a clone of MR memory. Your read one MR, save to *.bin file (RAW format and not encrypted, scrambled), and write it to another MR memory. The software module (MB MEMO) is especially useful for chip-tuning work and recovering unit after the broken update.
Function available thru OBD connection or direct connection with Direct Connect cable OBD connection support firmware access mode only. Direct Connect connection type support firmware and BSL (Boot Strap Loader) mode. BSL mode requires PLD cover disassembling.
Software module includes automatic checksum (main application and fuel map) recalculation.

2. License 2011+
For PLD memory read and write operation (category memo) PLD with XC2287 secured microprocessor.
Open access Read & Write memory for PLD, made on 2011 and later, with microprocessor Infineon XC2287.
Software module support PLD with firmware versions: 22B, 23E, 24B.
Does not support PLD with LOCKED firmware versions: 23F, 24C, 25B, 26x, 30C.

3. License MB KEYS
Key transponder programming module allows program up to 8 keys for Mercedes trucks, engine and drive control units.
Allows adding new keys for the Mercedes truck over OBD or DirectConnect cable with Transreader. Operations can be done offline, the only connection to the vehicle or ECU (PLD/MR) required.
It is possible to make up to 8 new keys without a resent key. Erase all programmed keys. Switch immobilizer system off (IMMO OFF) (required for vehicles with immobilizer faults). Or enable truck immobilizer system.

4. License MAN KEYS
Allows program transponder key to MAN truck and buses immobilizer memory.
Allows add up to 8 new keys, without MASTER KEY, for the MAN truck over OBD.
Key transponder programming can be done offline for MAN truck equipped FFR.

5. License FR.
Read/write FR or CPC by OBD
Immo off in FR and MR by OBD.
Supported FMR; FR; CPC; CPC1EU; CPC2EU.
Not all FR, CPC, FMR firmware versions are supported.
Not supported: CPC2 NAFTA; CPC2+ NAFTA; CPC4 NAFTA; CPC3; ADM2; ADM3.
DC-FR/CPC adapter not included.

6. License MB CALC
MB VeDoc and FDOK calculators – calculates access codes for VeDoc (X1, X2, X8) and FDOK ( XT, XN ) algorithms.
Must be used together with XENTRY (DAS) software and compatible diagnostic tool where these codes are asked. All operations are done offline, the only connection to the truck required for VEDOC.
For FDOK calculations not needed connection to the truck. FDOK code for new and old DAS.
DAS password generator – calculates password asked by DAS to access some special functions (MR downgrade from Euro4, Euro5 to Euro3)

7. License 3CORE
Read & Write full access for MCM and ACM control units memory over DirectConnect cable.
Type 1. Continental MCM1 (MCU TC1796-256F / TriCore 1 EEPROM M95128).
Type 2. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95640).
Type 3. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95640).
Not all MCM, ACM modules versions are supported.
DC-MCM/ACM adapter not included.

8. DirectConnect cable with Transreader inside.
DirectConnect cable to connect the VEI device directly to the MR (PLD). No need connection to the truck.
MR Flash and EEPROM memory read/write, key programming, diagnostic.

9. License MB DIAG
It able to Read DTC with the error description. Clear DTC.
Read and Erase fault codes.
VANs not supported.

10. License MB Extra
Speed limit change on MP3 trucks. (Applicable for FR and CPC drive control modules).
NOx torque limit.
Erase exhaust faults (AdBlue system fault source repair must be done firstly)